Lectures on Heat (3)

Thermal Expansion and the Gas Law
Coefficients of Expansion
Almost all materials expand on heating—the most famous exception being water, which contracts as it is warmed from 0 degrees Celsius to 4 degrees. This is actually a good thing, because as freezing weather sets in, the coldest water, which is about to freeze, is less dense than slightly warmer water, so rises to the top of a lake and the ice begins to form there. For almost all other liquids, solidification on cooling begins at the bottom of the container. So, since water behaves in this weird way, ice skating is possible! Also, as a matter of fact, life in lakes is possible—the ice layer that forms insulates the rest of the lake water from very cold air, so fish can make it through the winter.
Linear Expansion
The coefficient of linear expansion α of a given material, for example a bar of copper, at a given temperature is defined as the fractional increase in length that takes place on heating through one degree:

Of course, α might vary with temperature (it does for water, as we just mentioned) but in fact for most materials it stays close to constant over wide temperature ranges.


Volume Expansion
For liquids and gases, the natural measure of expansion is the coefficient of volume expansion,β.



Of course, on heating a bar of copper, clearly the volume as well as the length increases—the bar expands by an equal fraction in all directions (this could be experimentally verified, or you could just imagine a cube of copper, in which case all directions look the same).
The volume of a cube of copper of side L is V = L3. Suppose we heat it through one degree. Putting together the definitions of ,αβabove,





Gas Pressure Increase with Temperature
In 1702, Amontons discovered a linear increase of P with T for air, and found P to increase about 33% from the freezing point of water to the boiling point of water.
That is to say, he discovered that if a container of air were to be sealed at 0°C, at ordinary atmospheric pressure of 15 pounds per square inch, and then heated to 100°C but kept at the same volume, the air would now exert a pressure of about 20 pounds per square inch on the sides of the container. (Of course, strictly speaking, the container will also have increased in size, that would lower the effect—but it’s a tiny correction, about ½% for copper, even less for steel and glass.)
Remarkably, Amontons discovered, if the gas were initially at a pressure of thirty pounds per square inch at 0°C, on heating to 100°C the pressure would go to about 40 pounds per square inch—so the percentage increase in pressure was the same for any initial pressure: on heating through 100°C, the pressure would always increase by about 33%.
Furthermore, the result turned out to be the same for different gases!

Finding a Natural Temperature Scale
In class, we plotted air pressure as a function of temperature for a fixed volume of air, by making several measurements as the air was slowly heated (to give it a chance to all be at the same temperature at each stage). We found a straight line. On the graph, we extended the line backwards, to see how the pressure would presumably drop on cooling the air. We found the remarkable prediction that the pressure should drop to zero at a temperature of about −273°C.
In fact, if we’d done the cooling experiment, we would have found that air doesn’t actually follow the line all the way down, but condenses to a liquid at around −200°C. However, helium gas stays a gas almost to −270°C, and follows the line closely.

We shall discuss the physics of gases, and the interpretation of this, much more fully in a couple of lectures. For now, the important point is that this suggests a much more natural temperature scale than the Celsius one: we should take −273°C as the zero of temperature! For one thing, if we do that, the pressure/temperature relationship for a gas becomes beautifully simple:
P  ∝  T
This temperature scale, in which the degrees have the same size as in Celsius, is called the Kelvin or absolute scale. Temperatures are written 300K. To get from Celsius to Kelvin, just add 273 (strictly speaking, 273.15).
An Ideal Gas
Physicists at this point introduce the concept of an “Ideal Gas”. This is like the idea of a frictionless surface: it doesn’t exist in nature, but it is a very handy approximation to some real systems, and makes problems much easier to handle mathematically. The ideal gas is one for which for all temperatures, so helium is close to ideal over a very wide range, and air is close to ideal at ordinary atmospheric temperatures and above.